产品详情

自主研发的柴油发电机自动控制系统，

可提供给中大型柴油发电机组组装厂配套。系列产品涵盖单机、并机、自启动运转机组，并可配套市电发电自动转换柜(ATS)实现迅速启动柴油发电机组并切换至柴油发电机组供电。以提供酒店、消防、医疗等应急电力的紧急供应，可靠的设计及稳妥的调试； 有完全专业的工程设计师，并亲手进行调试，调试时间短，效果优异； 安全的线路排布 完全依照电气规范； 通用性强，适用于劳斯莱斯（PERKINS）、沃尔沃（VOLVO）、奔驰（MTU）、大宇（DAEWOO）、道依茨(Deutz)等国内外众多不同机型、不同容量机组的控制；
功能介绍：
        控制系统采用全自动化控制设计，可选择手动程序控制、自动程序控制、遥控等控制模式。
可设定柴油机的过程控制时间，包括：预热或预润滑时间、启动延时时间、启动限时、启动电机脱离转速、怠速运行时间、升速过程时间、冷却停机时间。
    可任意设定的柴油机额定转速值（非发电机应用时），自动监视发动机在启动、怠速、升速、全速等过程的速度变化，完成起动电机的投入与撤出、速度过高与过低的预报警及超限停机等。
    可设定报警限定值，自动实现超限预报警（不停机）、报警同时自动停机。
    预报警的项目包括：超速、低速、低油压、高冷却温度、高油温、低气温(低于4℃)、低燃油位、低冷却水位、低电池电压、高电池电压、转速信号未校准；
显示功能：
    柴油机运行状态显示：根据系统现时的实际情况，显示设备当前所处的状态：守侯、开机、供油、启动、启动延时、怠速延时、正常运行、冷却停机、紧急停机。（控制模块的左边输出灯显示当前运行状态）
    柴油机运行参数测量显示：在系统运行过程中，显示现时的有关参数值： 转速、冷却温度、润滑油温度、润滑油压力及通过副显示屏翻页显示运行时间、燃油油量、电池电压。
    柴油机报警状态显示：当系统出现故障报警，面板即在相应位置显示所出现的故障，说明报警类型（预报警或报警）、以及报警原因。
柴油机参数设置显示：显示当前系统设置的各个参数值，包括启动/停机过程延时状态设定值、运行速度控制设定值和全部的报警、预警参数设定值。

Independent research and development of automatic control system of diesel generators, is made available to the Assembly plant for large diesel generator unit in supporting. Product line covers single, and, since the start of operation units, and can support automatic conversion of AC power (ATS) for rapid boot and switched to diesel generator powered diesel generator set. To provides hotel, and fire, and medical, emergency power of emergency supply, reliable of design and the sound of debugging; has full professional of engineering designers, and personally for debugging, debugging time short, effect excellent; security of line arrangement full in accordance with electric specification; versatility strong, applies Yu Rolls Royce (PERKINS), and Volvo (VOLVO), and Benz (MTU), and large Yu (DAEWOO), and road according to Moskowitz (Deutz), both at home and abroad many different models, and different capacity unit of control;

Function:

Design of control system of automatic control, you can select manual program control, automatic program control, remote control mode.

Can be set to process control of diesel engines, including: pre or pre-lubrication time, initiated delay time, start time, start from the running time, speed, idling speed-speed process time, cooling down time.

Rated engine speed values can be set (non-generator), automatically monitor engine speed in starting, idling, litres, change of speed at full speed, complete start motor input and withdrawal of police, speed, high and low forecast and limit downtime.

Settable alarm limits, overrun pre-alarm automatically (without stopping), alarm and automatic stop.

Prediction of police items including: speed, low speed, low oil pressure, high cooling temperature, high temperature, low temperature (less than 4 ° c), low fuel level, low cooling water level, low battery voltage, battery voltage, higher speed signals are not aligned;

Display function:

Diesel engine running state display: according to the system's actual situation, and displays current status: wait, power, supply oil, startup, startup delay, idle delay time, up and running, cooling down, emergency stop. (Control output on the left side running lights display the current status of the module)

Measurement of diesel engine operating parameters display: during the system operation, displays the current parameter values: speed, cooling, temperature, oil temperature, oil pressure, and by Deputy display page display run timing, fuel quantity, battery voltage.

Diesel engine alarm status display: when the system has a fault alarm, fault of the Panel that appears in the appropriate location, description and alarm type (pre-alarm or alarm), and cause alarm.

Diesel engine parameter setting display: displays the parameter values for the current system settings, including start/stop status settings, speed control with time delay setting and alarm, warning of all parameters to the set value.